氣液增壓泵上下動很慢怎么辦？引起這個問題的原因有多種，請對照下面的故障原因來找到符合您的解決方法，作為參考使用。
What if the gas-liquid booster pump moves up and down slowly? There are many reasons for this problem. Please refer to the following fault reasons to find a solution for your reference.
故障原因：
Fault cause:
1、輸入的氣體壓力低。
1. The input gas pressure is low.
輸入的氣壓低使得氣液增壓泵的上升速度變慢或下降速度變慢。
The low input air pressure causes the rising speed or falling speed of the gas-liquid booster pump to slow down.
2、氣管很長或接口很小。
2. The trachea is very long or the interface is very small.
氣管很長或接口很小，使得氣體進入氣液增壓泵的速度慢或流量小，氣液增壓泵上下動就會(huì )很慢。
The gas pipe is very long or the interface is very small, so the gas enters the gas-liquid booster pump slowly or the flow is small, and the gas-liquid booster pump will move up and down very slowly.
3、氣液增壓泵的增壓部分出現背壓。
3. The pressurized part of the gas-liquid booster pump has back pressure.
4、氣液增壓泵產品選型問題。
4. Product selection of gas-liquid booster pump.
氣液增壓泵行程長短及出力噸位大小決定了氣液增壓泵上下動的速度,選購氣液增壓泵型號的時候，只考慮行程和出力大小，卻沒考慮到上下動的速度，沒對廠家說明速度上的要求。
The travel length and output tonnage of the gas-liquid booster pump determine the speed of up and down movement of the gas-liquid booster pump. When selecting the gas-liquid booster pump model, only the travel and output size are considered, but the speed of up and down movement is not considered, and the speed requirements are not explained to the manufacturer.
解決方法:
resolvent:
1、將氣體壓力低調標準狀態。
1. Lower the gas pressure to the standard state.
氣液增壓泵的氣體壓力要求在4~7kg/cm2，氣液增壓泵標準氣體壓力是6kg/cm2，不同有所區別，可咨詢生產廠家。
The gas pressure of gas-liquid booster pump is required to be 4~7kg/cm2, and the standard gas pressure of gas-liquid booster pump is 6kg/cm2, which is different from different brands. Please consult the manufacturer.
當使用氣體的設置添加了，氣體壓力就會(huì )變低或變得不穩定，為了穩定氣液增壓泵的動作速度及出力，可以在進前口前加裝JRN氣體增壓閥。
When the setting of using gas is added, the gas pressure will become low or unstable. In order to stabilize the operating speed and output of the gas-liquid booster pump, a JRN gas booster valve can be installed before the inlet.
2、縮短氣管及適當加大管路元件及氣管通徑。
2. Shorten the air pipe and appropriately increase the pipe components and the diameter of the air pipe.
氣管一般廠家都會(huì )配給用戶，每個廠家的默認氣管長度并不一樣，用戶對氣管長度有要求的，請在發貨前告訴廠家即可。接口很小，可聯系廠家重新配送管路元件及氣管通徑。
Generally, the manufacturer will allocate the air pipe to the user. The default air pipe length of each manufacturer is different. If the user has requirements on the air pipe length, please inform the manufacturer before shipment. The interface is very small, so you can contact the manufacturer to redistribute the pipe components and the pipe diameter.
3、重新設定氣液增壓泵的動作時間。
3. Reset the action time of the gas-liquid booster pump.
氣液增壓泵的四個動作（預壓下降、增壓下降、增壓回位、預壓回位）是依靠時間繼電器來控制的，可根據不同的產品的需求，通過時間繼電器來調整每個動作的時間。
The four actions of the gas-liquid booster pump (pre-pressure drop, pressure increase drop, pressure increase return and pre-pressure return) are controlled by the time relay. The time of each action can be adjusted by the time relay according to the requirements of different products.
4、從新選型訂購新的氣液增壓泵產品。
4. Order new gas-liquid booster pump products from the new model.
對氣液增壓泵上下動作速度有要求的，可考慮訂購JRM快速型氣液增壓泵、JRF單列式氣液增壓泵等速度快的型號。
If there is a requirement for the up and down action speed of the gas-liquid booster pump, it can be considered to order JRM fast gas-liquid booster pump, JRF single-row gas-liquid booster pump and other models with high speed.
用戶可以把使用要求具體詳細地告訴廠家，廠家會(huì )幫你匹配出適用的氣液增壓泵型號。
The user can tell the manufacturer the use requirements in detail, and the manufacturer will help you match the applicable gas-liquid booster pump model.
If the above methods cannot solve your problem, you can ask our gas-liquid booster pump manufacturer for help http://m.liqun518.com We will serve you wholeheartedly to answer your doubts!
