如何調節氣液增壓泵?對使用過氣液增壓泵的用戶來說是沒什么的,但是對初次使用者來說操作不當會(huì )導致被檢測件因為壓力過高而損壞,下面小編就給大家總結下初次使用要注意那些細節。
How to adjust the gas-liquid booster pump? It is nothing for users who have used the gas-liquid booster pump, but for first-time users, improper operation will lead to damage of the tested parts due to excessive pressure. The following brief section summarizes the details that should be paid attention to when using the pump for the first time.
1.初次使用要確保
氣液增壓泵是按廠方要求連接,不要用低于氣液增壓泵更高使用壓力的配件如:高壓管路,卡套接頭,高壓開關等。
1. First of all, make sure that the gas-liquid booster pump is connected according to the manufacturer's requirements. Do not use accessories with a higher working pressure than the gas-liquid booster pump, such as: high-pressure pipeline, ferrule connector, high-pressure switch, etc.
2.在使用合適的配件下按使用要求以此連接好,再檢查是否有泄露(液壓和氣壓不同稍微泄露會(huì )導致壓力浮動較大,再次增壓會(huì )形成脈沖對產品精細部件有影響)。
2. Use appropriate accessories to connect according to the use requirements, and then check whether there is leakage (slight leakage due to different hydraulic and air pressure will lead to large pressure fluctuation, and re pressurization will cause pulse to affect the fine parts of the product).
3.在滿足上述條件后再檢查驅動氣源是否滿足使用要求,被增壓的介質是否純潔和連接好
3. After meeting the above conditions, check whether the driving air source meets the operating requirements, and whether the pressurized medium is pure and well connected
4.完成以上步奏后打開驅動氣源,調節二連體上的壓力調節閥,從壓力0往高處調節所使用壓力,等氣液增壓泵高壓出口有液體排出時證明增壓缸內空氣完全排出,切斷驅動氣源,連接被檢測件再打開氣源。如果檢測在長時間內承壓能力就不用切斷氣源,檢測密封性2種辦法:1,切斷氣源看壓降2,保持氣源暢通看滲漏。
4. After completing the above steps, open the driving air source, adjust the pressure regulating valve on the duplex, and adjust the pressure from 0 to the used pressure. When liquid is discharged from the high-pressure outlet of the gas-liquid booster pump, it is proved that the air in the booster cylinder is completely discharged. Cut off the driving air source, connect the tested part and then open the air source. If the pressure bearing capacity is tested for a long time, it is unnecessary to cut off the air source. There are two methods for testing the sealing: 1. Cut off the air source to see the pressure drop 2. Keep the air source unblocked to see the leakage.
That's all for today's knowledge about gas-liquid booster pump. Please visit our website if you have any questions http://m.liqun518.com Let's provide you with more relevant information!