亚洲欧美综合区自拍另类,日韩欧美视频在线,日本一区二区三区在线网,综合欧美亚洲日本

熱線電話
0531-69951198
網站首頁
關于精拓
產品展廳
新聞中心
原理選型
客戶案例
在線留言
聯系我們
網站公告:

新聞中心

濟南精拓流體設備有限公司

電話:0531-69951198

郵箱:jingtuolt@163.com

傳真:0531-69951198

地址:濟南市歷城區祝甸北路2號院

網址:http://m.liqun518.com

企業動態

當前位置:首頁 - 新聞中心 - 企業動態訂購氣液增壓泵您需要知道

訂購氣液增壓泵您需要知道四個情況

發布時間:2022-10-21 13:49:37   發布人:http://m.liqun518.com
要使您的氣液增壓泵處于很好的工作狀態,訂購氣液增壓泵要注意四個事項,下面小編為您整理下看看吧。
In order to keep your gas-liquid booster pump in good working condition, you should pay attention to four items when ordering the gas-liquid booster pump. The following sections will sort them out for you.
1.氣液增壓泵的驅動氣體的壓力和流量。
1. Pressure and flow of driving gas of gas-liquid booster pump.
在連續工作時,所有的氣液增壓泵和動力單元使用的驅動氣壓不超過0.69Mpa,在間歇工作時可達到1.03Mpa。
During continuous operation, the driving air pressure used by all gas-liquid booster pumps and power units shall not exceed 0.69 Mpa, and can reach 1.03 Mpa during intermittent operation.
2.氣液增壓泵的工作壓力和流量。
2. Working pressure and flow of gas-liquid booster pump.
所有的氣液增壓泵和動力單元的工作壓力參照驅動氣壓為0.48Mpa時泵輸出壓力和流量。如果泵的大輸出壓力大于所需的工作壓力,這就要考慮做好措施以免發生意外。
The working pressure of all gas-liquid booster pumps and power units shall refer to the pump output pressure and flow when the driving air pressure is 0.48Mpa. If the large output pressure of the pump is greater than the required working pressure, safety measures should be taken to avoid accidents.
氣液增壓泵
3.氣液增壓泵的輸送液體介質。
3. Delivery liquid medium of gas-liquid booster pump.
氣液增壓泵輸送的液體介質是選型中著重考慮的部分。液壓部分的材質和液壓密封圈是由輸送的液體介質所決定的。氣液增壓泵可用油、水和大多數液體介質。
The liquid medium delivered by the gas-liquid booster pump is a key part of the selection. The material of the hydraulic part and the hydraulic seal ring are determined by the liquid medium conveyed. The gas-liquid booster pump can use oil, water and most liquid media.
標準泵的主要液壓密封圈是丁橡膠和聚氨酯,單向閥座采用特氟龍密封。其它密封材料包括碳氟化合物和亞乙基丙烯,這些密封材料主要用于輸送的特殊介質。
The main hydraulic sealing rings of the standard pump are polybutadiene rubber and polyurethane, and the one-way valve seat is sealed with Teflon. Other sealing materials include fluorocarbon and ethylidene propylene, which are mainly used for special media.
4.氣液增壓泵的體積和重量。
4. Volume and weight of gas-liquid booster pump.
對于某些的應用,泵和動力單元的外形尺寸和重量也要考慮。
For some applications, the overall dimensions and weight of pumps and power units should also be considered.
以上就是問題的相關解答了,您對此有什么想法要分享的嗎?可以隨時來我們網站http://m.liqun518.com進行咨詢了解!
The above is the answer to the question. Do you have any ideas to share? You can come to our website anytime http://m.liqun518.com Ask about it!
新聞: